Бамбэй
Мастер чайного рынка

BAMBEY — TEA-MARKET SPECIALIST
Experimental resin Beta package · r009 v008 · 80 mm · UNCALIBRATED

This partial resin package contains the unchanged upright 80 mm figure STL, an editable 3MF with TWO MESH VOLUMES (figure and supports, not native contact handles), the exact final CTB, actual parameters of all 1600 layers and a guide. No firmware execution, physical calibration or test print has been performed.

Digital author and independent QA passed: all1600 Z positions, extended headers, format-transformed rasters and roundtrip RLE payloads; selected islands/bounds/height/empty-layer issues:0. CTB's 7-bit grayscale transformation is respected; original8-bit identity is not claimed. Only joined support pair08/09 was changed;161 other components are identical and retain inherited review provenance. This is not a fresh individual inspection of every contact.

TARGET: Phrozen Sonic Mighty Revo16K,15120x6230,211.68x118.37x235mm. SUNLU14K ABS Grey (standard, not water-washable), room target25C; resin temperature unmeasured. This is an engineering starting profile, not vendor-certified or physically calibrated. Do not reuse automatically for SUNLU Wax or another resin.
Layer0.05mm;6 bottom layers25s;10 transition layers; normal2.5s. Lift2+10mm at60/120mm/min. Retract10+2mm at180/120mm/min. Wait-before-cure1s; other waits0; light-off-delay0;PWM255. MirrorX=true,Y=false physically unverified. Extended headers are authoritative for every layer; a global bottom-wait display may show0. Actual firmware behavior remains untested. UVtools calculated estimate24275.61s (~6h45m), not measured print time. Figure height80mm is measured upright without raft/supports; do not rescale from the tilted assembly height.

CONDITIONAL SUPPORT REMOVAL
1. Locate joined pair08/09 in the 3MF and guide. Orange is support, grey is unchanged figure. Do not try to insert two jaws between the close upper tips. All coordinates below are slicer-scene mm, not measurements from the figure's feet.
2. Common lower cut: Z51.386854mm, kerfZ51.326854..51.446854 (0.12mm); X113.042179..114.427952,Y50.571780..52.370139. The calculated blade enters from positiveX toward negativeX, then withdraws along the same route. Only support material is cut.
3. Jointly separate upper tips08/09: nominal diameter0.18mm, axial half-height0.10mm; centers08=(112.469356,53.741838,52.119950),09=(112.443762,53.622862,52.127833). The ideal proof removes all support material inside these two predefined contact domains; real fracture does not guarantee this result. Inspect remnants; never compensate for a snag by increasing force.
4. Move the entire detached joined piece horizontally, without rotation, in direction(+0.5,-0.8660254,0). Green in the guide is the same piece after2mm, not another support. Lower stumps and all161 other components remain obstacles. The full45.552438mm route establishes mathematical escape beyond all obstacles, not a required physical travel distance.
5. Lower stumps remain. Their later cleanup, fracture force and surface marks have not been physically verified.

IDEAL TOOL LIMITS
This is a conditional thin beveled blade, NOT a two-jaw cutter:0.12mm thick,1.835mm maximum width,24.720743mm reach to a25x6x6mm handle. Full entry volume was checked. No real commercially available tool was confirmed. Real blade profile/teeth/flex and grip must fit the tested envelope; otherwise the proof does not apply. Minimum ideal blade-to-figure gap~0.0549mm. Certified route lower bound~0.002665mm after numerical allowance is a mathematical bound, NOT a printer tolerance. Resin residue, roughness and deformation may obstruct the route. Stop if the real tool does not fit or the part catches/bends; damage-free removal is not promised.

EDITING/REBUILD
The3MF stores separate meshes and PrusaSlicer settings, not native support contacts. Final CTB staged motion, waits and transitions were applied after conversion and are not fully stored in the Prusa project. The INI is an input for the included offline helper, not a native printer/slicer import profile; CSV is actual readback, not an import preset. Any geometry/support/scale/profile change requires reslice→CTBv4→profile application→all-layer raster/Z/profile/issues QA→author+independent review. Old CTB does not match edited geometry. See Rebuild/README.txt.

Before physical use: verify actual printer, material, mirror, temperature/exposure, support retention and tool access. A shared separate diagnostic coupon is linked below; it is also UNCALIBRATED and does not prove this figure printable.
https://media.thetea.app/tea-toys/downloads/digital-kits-2026-10-23/shared/resin-diagnostic/c8883a707f07f679/TEA-Shared-Resin-Diagnostic-SUNLU-ABS-Grey-Revo16K-UNCALIBRATED.zip
SHA256 c8883a707f07f679bb8bd66e9b7f0ef2d9f016cbc89e20b9c9ca12eada41071f ·3968960bytes.

Non-commercial use only: personal printing, learning and experiments. Selling files or printed items requires separate permission.