Бамбэй · Мастер чайного рынка / Bambey · Tea-market specialist — PLA / Bambu Lab A2L / сопло 0.4 мм

UNCALIBRATED — физическая калибровка и проба ещё не выполнены.
Материал: SUNLU PLA BASIC Grey. Пластина: Textured PEI. Комната: 25 °C по заданию.
Фигурка: 80 мм без опор; вертикально, масштаб 100%. Слой: 0.08 мм.
Сопло/стол: 210/60 °C; это начальные значения, не измеренный профиль катушки.
Поддержки: Tree Slim auto, порог 30°, от платформы и от модели; верхних интерфейсов 3, нижних 2; верхний/нижний Z-зазор 0.16/0.16 мм; brim 5 мм.
Время слайсера: 6 ч 45 мин. Расход слайсера: 36.97 г.

Открыть *__supports-editable.3mf в Bambu Studio 02.08.02.61, чтобы редактировать модель, размещение и параметры автоматических опор. Деревья вычисляются заново при нарезке; вручную редактируемые контактные точки здесь не заявлены.
*.gcode.3mf — рассчитанное машинное задание для точной указанной комбинации.
После любого изменения геометрии, ориентации, материала, опор или калибровки заново нарезать и проверить траектории.
Цифровая проверка пройдена; физическая калибровка и пробная печать отложены. Индивидуальная визуальная проверка не заменяется наличием файла или нулевым кодом завершения.
Печать из этой программы не запускалась. Физический допуск не выдан.

ENGLISH OPERATOR NOTES — Бамбэй · Мастер чайного рынка / Bambey · Tea-market specialist
UNCALIBRATED. Digital file checks and individual support/toolpath reviews passed;
physical calibration, adhesion, support removal and print quality are untested.
Only this exact printer/nozzle combination may use the supplied sliced file.
Printer: Bambu Lab A2L. Nozzle: 0.4 mm.
Material: SUNLU PLA BASIC Grey. Plate: Textured PEI. Room target: 25 C.
Figure height without supports: 80 mm. Upright Z-up placement; no rotation.
Layer height: 0.08 mm. Nozzle/bed: 210/60 C (starting values).
Walls: 2; generator: arachne.
Infill: 15% gyroid.
Supports: tree(auto), tree_slim, threshold 30 degrees;
from bed and model; small overhangs retained.
Top/bottom interface layers: 3/2.
Top/bottom contact Z distance: 0.16/0.16 mm.
Brim: outer_only, 5 mm.
Slicer estimate: 24303.055 seconds (405 minutes), 36.9680 g.
Estimates include supports; they are not measured print time or material use.
Open the supports-editable 3MF in Bambu Studio 02.08.02.61 to edit model,
placement and automatic-support settings. Contact points are generated again
when slicing; this file does not claim manually editable native contact points.
The .gcode.3mf contains the actual calculated toolpaths. After any setting,
geometry, support or calibration change, slice again and inspect the result.
Previews.html provides labelled model/support/contact diagrams from these paths.
Diagrams show nominal toolpath centre lines, not a physical extrusion simulation.

Shared diagnostic reference: TEA detail coupon — Bambu-A2L — 0.4 mm — SUNLU PLA BASIC Grey.
The collection supplies this coupon once per exact printer/nozzle/material profile.
The coupon checks detail/slot reproduction; it does not calibrate flow or pressure advance.
The initial physical studio trial is A1 mini / 0.4 mm; no print has been dispatched.
Model profile fingerprint SHA256: 25ad90e8a71bc4eaac68480327917d806e4c3ff2374b2bb5871465fa3f47946d
Editable SHA256: 8644d7baaf8b11995834a0d321bed76b1367db77f8329b64dcf5daf68d4efba7
Sliced SHA256: 0f5808fba7970edcb1e6a3f4772a8375a8923898153f30aba6224cb5dde7bd2e

Only non-commercial use: personal printing, learning and experimentation.
Selling files or prints requires separate permission.
Только некоммерческое использование: личная печать, обучение и эксперименты.
Продажа файлов и отпечатков требует отдельного разрешения.
